Toilet Flush Hook

There's nothing worse than finding that your toilet won't flush, but there's no need to panic as it's easily sorted. Watch this how-to video from Homeserve for a no nonsense guide on how to get your toilet working again. Step 1: First off, lift the cistern lid and check that ...more

Some toilets just don't have enough flushing power. As in, when you flush the toilet not all of the, er, stuff, goes down. As a result you have to flush the toilet twice, wasting water and your time. Turbo charge your toilet flushing by checking out the tip in this video, whi ...more

In this tutorial, we learn how to install a dual flush toilet kit. First, grab the directions from the box that the toilet came in and read them! After this, you will take the lid off the tank of the toilet. Then, install the flusher into the tank of the toilet after removing ...more

This video tutorial is in the Home & Garden category which will show you how to save money & water with your toilet flush. The first step is to turn the water off. Then remove the lid of the tank, disconnect the bowl refill supply and make sure that the overflow pipe is open. ...more

This is a how-to video about measuring the toilet flush volume. This is a handy method to find out how much water is used for flushing your toilet. Here is the step by step technique to measure the water capacity of your toilet. 1)Turn of the water supply to the tank to the f ...more

Learn how to troubleshoot a toilet that won't flush at your home in simple steps. First lift the lid and check whether the float ball is broken or touching the sides. Bend it a little if its touching the sides or replace it if its leaking or broken. Now check condition of the ...more

In this video learn how you can save money on water every time you flush the toilet by converting your toilet into a low flush toilet.

Separate restroom hygiene fact from fiction – here's how. You Will Need * The first or last stall * Hand-washing Step 1: Choose the right stall Choose the first or last stall. The middle ones usually get the most traffic, and therefore contain the most bacteria. Step 2: Hang ...more

Normally, when you press the lever on your toilet in your bathroom, you expect it to flush, but sometimes your toilet just won't flush completely, or you have to hold the lever down to get it to work. Lowe's tells you that the problem might be the flapper, and they show you ho ...more

Watch this video from This Old House to learn how to repair a pressure assisted toilet. Steps: 1. Turn off water to toilet by closing the shut-off valve. 2. Flush the toilet to empty tank. 3. Disconnect water-supply line from toilet. 4. Unbolt tank and lift it off toilet. 5. ...more

Toilets are one of the greatest boons to public health of all time, but they do use a ton of water when they flush. If the old adage "If it's yellow, stay mellow. If it's brown, flush it down," disgusts you, but you still want to find a more green way to flush, then watch this ...more

We really dislike toilets that flush slowly. You have to wait an eternity for all the water to go down, and then it slowly muddles on to an annoyingly weak flush that doesn't make all the er, stuff, go down. Toilets weaken with age, making the flush weak, but there is a way to ...more

In this video we learn how to install a toilet water inlet valve. First, turn the water off and flush the toilet to get rid of the water in the system. From here, pull out the flush valve by turning it clockwise and lifting it. Then, grab your new valve and replace it where th ...more

Watch this video from This Old House to learn how to fix a running toilet. Steps: 1 Turn off the water at toilet's shut-off valve. 2 Remove the rubber flapper from flush valve inside the tank. 3 Inspect flapper for damage or discoloration. 4 Check location of float on chain; ...more

This how-to video explains the hydrostatic pressure. The video provider explains this effect by asking a question, "How are toilets able to flush without a pump?" To understand this, a knowledge of hydrostatic force is important. To understand the hydrostatic pressure, take t ...more

This video shows you how to unclog a toilet using a plunger. Usually a toilet clog is caused by too much toilet paper. If the water runs out of the toilet, use towels on the floor to absorb excess water. You should place the plunger down into the toilet at an angle and start p ...more

Watch this video from This Old House to learn how to fix a wobbly toilet. Steps: 1 Turn off water to toilet by closing shut-off valve. 2 Flush toilet and hold down the lever to empty tank. 3 Sop up remaining water from tank and bowl with sponge or turkey baster. 4 Use adjusta ...more

In this tutorial, we learn how to replace a broken flush handle. First, remove the top from the tank on the back of the toilet. After this, find the chain that is connected to the handle and remove it. From here, take a new handle and place it into the spot the old on was in. ...more

FusionGuy09 tells us how to fix a leaky toilet. You should be able to hear the leaking toilet. First thing you want to do is turn the water off. You can do this by reaching behind toilet and turning a lever. Next, flush the toilet to remove the water from the tank. Remove the ...more

In this tutorial, we learn how to replace and install a toilet with Lowe's. To get started, you will first need to turn off the water to your home, then take measurements around the toilet. Next, remove the top of the tank, then flush the toilet and remove excess water. After ...more

To install the new toilet you will need a putty knife, hacksaw, tape measure, adjustable wrench, level, sponge, and replacement wax seal. Before you begin removing the old toilet, turn off and disconnect the water supply to the toilet. Then flush the toilet to get the water ou ...more

Trim down your water bill and do the planet a favor by adjusting the water height in your toilet tank. The Fluidmaster's float cup on the fill valve can easily be adjusted to set water height in the cistern, just by fine-tuning the water level adjustment clip. This process is ...more

This Home & Garden video shows you how to replace a running old style fill valve toilet with something more modern. Shut the supply line to the toilet and flush to remove the water from the tank. Then remove the supply line. Now take a wrench and loosen the plastic nut of the ...more

Bob Schmidt from Home Remodel Workshop demonstrates how to frame a wall 16 inches on center. His tutorial is especially helpful, so pay attention to his tips, tricks, and specific techniques. When laying out a top and bottom plate for a typical wall a framing square is usuall ...more

We’ve all had the problem of a toilet that just won’t stop running. You can fix this problem yourself with a few tools from the local hardware store. The part that is causing the excess running is an old fill tube and stopper valve. You will want to shut the water off to your ...more

The handle on your toilet is the most common way you interact with the device, and if it breaks your toilet is much harder to flush. Watch this video to learn how to remove the broken handle and install a new one.

First, apply wax to the toilet hole so it doesn't leak. Next install the supply line. Set the bolts on the flange and attach a wax ring onto the bottom of the toilet. Set the toilet over the bolts. Next, stick the gasket to the bottom of the tank and put the tank on the toilet ...more

In this video, we learn how to fully remove a tick. Ticks can carry diseases, so it's best to get rid of these right away, checking your pet daily. Find the tick and then grab it as close as you can to your pet's skin. Pull it out and make sure you've gotten all the parts. The ...more

In this plumbing repair video, you will learn how to install a new toilet complete from wax ring to water hook up. This is for plumbing in a typical home.

A hungry tick is a determined little bugger—it wants to find its way into your skin if it’s the last thing it does. Here’s how to make sure it is the last thing it does. You Will Need * A pair of fine-tip tweezers * Some rubbing alcohol * Cotton balls * Warm water * Soap * A ...more

Is there anything worse than a leaky toilet? One minute you're flushing the tank and the next you're standing in a pool of water and ruining all your nice towels. In this tutorial, Tool Dude Tony walks you step by step through the process of replacing all the parts in a toilet ...more

You may want to replace the toilet in your bathroom for a number of reasons. Perhaps you have a cracked toilet, an antiquated model or one that uses a significant amount of water. There are a number of new models which will match the decor of your home and reduce the amount of ...more