Adjust the Valve

How To : Adjust the valve lash when building an engine

In this video you will learn how to adjust the valve lash - one of the necessary steps of building an engine. You want to leave as much of the internal lubrication in place as possible. If you follow the firing order of your motor, you'll only have to turn the crankshaft one c ...more

How To : Adjust the valves on a 2 valve Ducati

Learn how to adjust the valves of your Ducati. This video applies to all 2 Valve Ducatis. Part 1 of 2 - How to Adjust the valves on a 2 valve Ducati. Part 2 of 2 - How to Adjust the valves on a 2 valve Ducati.

How To : Adjust the valves on a 1996 Honda Civic

Having clean, functional valves is essential to proper engine function. Honda cars need to have their valves adjusted when they start to make noise. In this video you will learn how to adjust the valves on a 1996 Honda Civic.

How To : Check and adjust the valves on a KLR650

In this motorcycle tutorial you will learn how to check and then adjust the valves on a Kawasaki KLR650 motorcycle. You will need to remove the bodywork of the bike first. Once you've done that, watch this video and get ready to do a valve check on the KLR and then a valve adj ...more

How To : Fix a sweating toilet tank with This Old House

Watch this video from This Old House to learn how to fix a sweating toilet. Steps: 1. Turn off water and drain the pipes. 2. Cut a tee-fitting into a nearby hot-water water pipe. 3. Dry-assemble the various copper pipes and fittings to the anti-sweat valve. 4. Solder together ...more

How To : Troubleshoot a toilet that won't flush

There's nothing worse than finding that your toilet won't flush, but there's no need to panic as it's easily sorted. Watch this how-to video from Homeserve for a no nonsense guide on how to get your toilet working again. Step 1: First off, lift the cistern lid and check that ...more

How To : Service a Peugeot 206 Compact Car

This video gives a step by step tutorial how to service a Peugeot 206 with the 1.4 liter engine. Please note that the video is not in English, but you can follow along by watching the video and following the written instructions below. Work under the car. Change the oil and r ...more

How To : Fix a running toilet with This Old House

Watch this video from This Old House to learn how to fix a running toilet. Steps: 1 Turn off the water at toilet's shut-off valve. 2 Remove the rubber flapper from flush valve inside the tank. 3 Inspect flapper for damage or discoloration. 4 Check location of float on chain; ...more

How To : Adjust the flame on your RV water heater

In this video, we learn how to adjust the flame on your RV water heater. First, open up the area where your gas valves are. Find the air opening to make a smaller air adjustment. The setting should be 1/4 of the way open. Snug down the locking screw when you have adjusted it p ...more

How To : Build a waterfall using retaining wall block

The procedure was adopted to build a waterfall in Oregon Coast Garden Center, Wald-port. 1. A level pad was cut to arrange the first row of blocks 2. 3 rows of retaining wall block was set in the desired shape. 3. The inside of the structure is covered with landscape fabric fo ...more

How To : Tune the ACME Attacker 1/8 scale RC Nitro engine

This video shows you how to tune the ACME attacker 1/8th scale nitro engine buggy. Use the high end valve and the idle speed screw as show in the film. Turn the engine and get it to the operating temperature and drive round to the see how the car performs. If the acceleration ...more

How To : Bleed and adjust trailer brakes

In this video, we learn how to bleed and adjust trailer brakes. First, level the trailer and use a jack stand to support it. Now, hand bleed the brakes using the master cylinder. From here, let any air out of the break line, doing this on all the different brake lines. Next, f ...more

How To : Change a road bike tire

This how-to video demonstrates how to change the tire of a road bike. First of all, the old tube must be removed with the help of some tire levers. The new tube that will fit the rim must be inflated at an optimal 5 psi. The tube will then be mounted on the rim starting with t ...more

Make Your Own Nitrous Oxide : Hilarious Science

If you've ever had teeth removed/minor surgery, you most likely received some laughing gas, or nitrous oxide. This gas creates a happy, lightened feeling, and causes instant laughter. In this article, I'll show you how to make some. BUT BE CAREFUL!!! DO NOT proceed in this exp ...more

How To : Repair a toilet tank

The video describes how to replace the fill valve, the rubber flapper, and an older plastic water fill line with a stainless steel one so that the toilet will no longer leak. Purchase a fill valve kit at your local hardware store before beginning. Start by turning water compre ...more

Next Page
Prev Page
  • Hot
  • Latest