Sure, your RC car runs like a champ but does it look the part? With a little bit of customization, it can. In this hobbyist how-to, you'll learn how to add mask and fade detail to an RC shell. Part 1 of 2 - How to Add mask and fade detail to the shell of a toy car. Part 2 of ...more
This prank is inspired by my "airbag couch prank". Place at least 2 airbags in the ground and tell someone that we are playing hide and seek and have them stand over the airbags. Have them "count down" while you go hide. The time till the airbag goes off!! While they think ...more
In this tutorial, we learn how to install a new engine in an RC Nitro Truck. First, fix the engine fly wheel and then fix the clutch shoes. After this, fix the drive gear by making sure the bearings are fit into place. Next, put the drive gear on, then make sure there isn't an ...more
In this how to video, you will learn how to install and replace the glow plug in your RC car. Glow plugs are used to ignite the fuel in the engine. A glow ignition makes the filament in the plug red hot. To check if the glow plug works, place it on the ignition and check if th ...more
This video shows the basic steps to starting a cold RC nitro engine. • Remove the body cover of the RC car, exposing the engine. • Cover the exhaust and pull the starter chain a few times to fill gas lines and prime the engine. • Now, without covering the exhaust pull the star ...more
While it seems like nit-picking, there is a proper procedure for turning an RC toy car on and off. Going out of the proper order can result in accidents from runaway cars or even damage to the RC toy. Watch this video tutorial and learn how to turn an RC vehicle on and off whi ...more
Alishan Mao describes how to fix a flooded Nitro Engine on an RC car, remove the excess fuel, and start the engine. Flooding of the engine can occur when priming the engine. If you prime the engine too much, the engine can get flooded, making it difficult to pull the pull star ...more
In this video, learn how to strip a magnet wire for soldering when making mini-RC cars. This process is incredibly easy to do and you will be surprised how fast it works. So, check this out and assemble your cars faster and easier.
If you call yourself a hobbyist or a kid at heart, you know that remote-controlled vehicles are more than just fun. If you're a serious R/C man, you'll know all about doing everything to your model truck or car, like fixing wheels, vamping the pinion gears, waterproofing, trou ...more
This video shows how to drift with electric and petrol(nitro)model RC cars. Learn how to develop the right skills and find the right parts to drift with a toy model car.
If you're like me, you were always jealous of the kids with rich parents who got to ride around in their own Power Wheels cars. Now that I am tall enough to sell my body and time, I find myself attaining childhood dreams like buying my own Power Wheels car. I would not have ch ...more
Deep in their heart of hearts, most Americans dream of having their car festooned with missile launchers and machine guns. Anyone who cuts them off or looks at them funny in traffic could be dispensed with quick and extreme justice, leaving a real-life James Bond and his passe ...more
It's always handy to waterproof your RC kit because your toy car is going to tread in a lot of dirty - and sometimes wet - ground. This means that any electric circuitry faces the risk of coming in contact with water and fizzing out. So keep things safe by learning how to wat ...more
If you own a Traxxas Rustler, Stampede Bandit, or Slash RC vehicle, then this next tutorial may be for you. In the tutorial, you'll be finding out how to clean the transmission to your machine. Just like a car, keeping your RC vehicle in tip top shape is important for ensuring ...more
For most automotive applications a battery needs to supply a lot of current for a short period of time to turn over the engine and get the car started. With the engine running, the car's alternator produces all the power the car needs. Thin plates inside a starting battery inc ...more
In this next video tutorial, you'll be finding out how to properly balance the wheels on your RC. Balancing them is important, just like a regular car, in making sure they work properly, don't wear out so soon, and will perform much better. It's not difficult to do and require ...more
People who may be getting into the hobby of building RC vehicles, need to know which is the best fit for their cars. Purchasing the wrong tires can lead to unnecessary damage and a waste of money. In this tutorial, you'll be finding out the difference between LPR and VTR tire ...more
Just like cars, RC vehicles need to be kept in fine shape in order for them to work properly. Doing so will result in a long lasting and healthy vehicle. In this tutorial, you will learn some tips and tricks to putting an RC engine back together again, after you've worked on i ...more
This video is on how to test an RC (radio controlled) nitro engine for air leaks and also gas tanks for leaks. You need to take care of your radio controlled vehicle just as you would your real car.
First of all you have to loose the altitude by taking a circle or two around in the air. On the final turn make a good straight approach to runaway and don't use too much ‘ailerons’ then. Just use the controls ‘rudder’, ‘elevator’ and ‘throttle’. Also watch for the cars or the ...more
This German video is amazing. A joyously analog interpretation and deconstruction of the digital gaming experience. Malte Jehmlich is as primitive and inspiring as the the Vanuatu natives who devoted themselves to cargo worship after World War II! Try to imagine. It's 2010 an ...more
If you need help balancing our tires on your RC vehicle, this tutorial should help. Like a regular car, tire balancing is very beneficial since it can make things last a lot longer and make your RC drive smoother. This video covers the different balancers that are out on the ...more
You'd think a Hummer couldn't get any more over-the-top (unless you're talking a horse-drawn Hummer or remote-controlled Hummer, of course), but Japanese tuner Calwing’s US division, 213 Motoring has come out with a Hummer boasting a whole extra set of wheels. I'm not quite su ...more
Squirrelod shows you how to put together a shock assembly or a shock absorber on a Factory Team remote control car kit. He takes us through building the piston - shaft, dampener, nuts and over rings step by step. Practical tips and tricks involved in building up the shaft and ...more
For all you future RC fans out there, if you're having trouble setting the Nitro engine gear mesh up on your RC vehicle, do we have the video for you. This tutorial will give you about 8 whole minutes of how to properly set up this easy task. Although it says it is for Nitro, ...more
In this quick video tutorial, find out how to glue and balance the tires on an RC kit. Finding out how to glue and balance your tires is important since tires make your car go! So enjoy this quick and easy tutorial for all you RC freaks! Squirrel's Twitter- SquirrelToyz Chec ...more
In this how-to video, you will learn how to put back a 2 speed central gearbox in your RC vehicle. Take the time to clean your car. Remember that the shorter dog bone goes to the rear and the longer one goes to the front. Slide the dog bone in and make sure that it spins the w ...more
This video shows you how to tune the ACME attacker 1/8th scale nitro engine buggy. Use the high end valve and the idle speed screw as show in the film. Turn the engine and get it to the operating temperature and drive round to the see how the car performs. If the acceleration ...more
If you call yourself a hobbyist or a kid at heart, you know that remote-controlled vehicles are more than just fun. If you're a serious R/C man, you'll know all about doing everything to your model truck or car, like fixing wheels, vamping the pinion gears, waterproofing, trou ...more
If you call yourself a hobbyist or a kid at heart, you know that remote-controlled vehicles are more than just fun. If you're a serious R/C man, you'll know all about doing everything to your model truck or car, like fixing wheels, vamping the pinion gears, waterproofing, trou ...more
If you call yourself a hobbyist or a kid at heart, you know that remote-controlled vehicles are more than just fun. If you're a serious R/C man, you'll know all about doing everything to your model truck or car, like fixing wheels, vamping the pinion gears, waterproofing, trou ...more
RC Car Action Magazine Editor Matt Higgins shows us some open wheeled modified oval cars and also how to properly set gear mesh. The trick to setting gear mesh is a scrap piece of paper. Watch this video tutorial and learn how to set gear mesh on an RC car.
RC Car Action Magazine Editor Paul Onorato shoes a neat tip on cutting perfect body posts. Most cars come with body posts that are too long, but cutting them can warp the post. Watch this video tutorial and learn how to trim body posts for an RC car.
RC Car Action Magazine Editor Kevin shows you how to stop a nitro engine. Just bump the flywheel with a screwdriver or pinch the fuel line. Watch this video tutorial and learn how to stop a nitro engine on an RC vehicle.
This video tutorial shows tips on applying Liquid Mask to your RC car body prior to painting. Liquid mask takes the place of masking tape while painting. Watch this video tutorial and learn how to easily prep the body of an RC vehicle before painting.
RC Car Action Magazine Edito Paul Onorato demonstrates how to remove and install clutch shoes using a DuraTrax clutch shoe tool. The clutch show tool makes the clutch easy to install and remove. Watch this video tutorial and learn how to use the clutch shoe tool on a remote co ...more
Paul Onorato, senior editor of Radio Control Car Action magazine shows you how to remove a clutch nut and flywheel from a nitro engine. It's difficult because a wrench spins and pliers can pinch. Watch this video tutorial and learn an easy way to remove a clutch nut and flywhe ...more
If you call yourself a hobbyist or a kid at heart, you know that remote-controlled vehicles are more than just fun. If you're a serious R/C man, you'll know all about doing everything to your model truck or car, like fixing wheels, vamping the pinion gears, waterproofing, trou ...more
If you call yourself a hobbyist or a kid at heart, you know that remote-controlled vehicles are more than just fun. If you're a serious R/C man, you'll know all about doing everything to your model truck or car, like fixing wheels, vamping the pinion gears, waterproofing, trou ...more
On Friday, game developer PreviewLabs released the first online multiplayer game for the Microsoft HoloLens. Available for free on the Microsoft Store, Buggy Blasters is a real-time strategy game in which players place and navigate armies of virtual remote control cars. Using ...more
Aside from being completely adorable, Fijibot is a completely autonomous robot that automatically seeks out light sources to charge his solar-powered battery. He's built from a 1.5 liter Fiji water bottle, packed with an Arduino Uno, 6 volt solar panel, and an Arduino Proto Sh ...more
Super Mario Bros. is one of the most renowned games in history. It helped resurrect a dying video game industry in the mid-'80s and still remains one of the best-selling video games of all time—one reason why the new NES Classic Edition is so popular and impossible to get thes ...more
More redneck fun. Bob Moravitz plus family and friends have created an 8 hour event of propelling vehicles off cliffs. Held yearly, admission is free but donations are encouraged (to cover insurance costs). "“The idea was inspired last year by boredom and a strong desire to d ...more
I love robots. They have the potential to evolve into Asimovian destroyers of the human species, but have only just mastered the art of cleaning my rug. They have an ever increasing cool factor and a growing number of cheap and simple components that let the hobby roboticist r ...more
Smartphone gaming continues to improve with ever sharper displays and raw processing power to deliver console-quality graphics right in the palm of your hands. Nonetheless, you still stand to improve the gaming experience on any phone by adding the right accessories to the mix ...more
Buckle up, iPhone users, because it's update time! Apple just released its latest iPhone OS to the public, iOS 14.4. This new edition isn't the company's most ground-breaking, but it doesn't come up short, either — you'll find support for smaller QR codes in Camera, a new "Dev ...more
Need a unique gift idea for the techy person in your life? Look no further than that phone they always have in their hand. There are plenty of great accessories, apps, subscriptions, and other smartphone-related goodies that will improve their quality of life, and thoughtful g ...more