G Clamps

How To : Install the X-Clamp mod fix to your Xbox 360

Take a look at this tutorial to learn how to install the X-Clamp mod fix for your Xbox 360. In this video, the instructor only ordered one set of washers and so when he accidently drilled the wrong side on the metal case, he was forced to improvise. Instead of using 4 screws a ...more

How To : Use the Manfrotto Super Clamp

Did you ever have trouble keeping a steady shot with a camera or camcorder when you didn't have a tripod ready? In this video, Steve from Cameras Brookwood shows you why a Manfrotto Super Clamp might just be the tool for you. A Super Clamp can open up to three inches and attac ...more

How To : Make your own solid pipe clamp hold-down

In this video "A better way" presenter Chuck Miller demonstrates a method of how to create a job site pipe holder (clamp hold-down) as opposed to a c-clamp, bar clamp or blocks of wood. It involves use of a pipe flange of the same diameter as the pipe being held. It shows you ...more

How To : Make a clamp when you don't have one

Get some simple home repair and improvement advice from the H.O.W. TV team. Watch this video tutorial to learn how to make a clamp when you don't have one. See the good and bad that goes along with home repair. Watch Pam Melton from HOWTV improvise a clamp using pieces of car ...more

How To : Build a simple miter clamp

In this Home and Garden video tutorial you will learn how to build a simple miter clamp. Chuck Miller in this video explains how simple and easy it is. When you glue in two parts together, you need to hold them in place so they join firmly. A simple way of doing this is by a m ...more

How To : Start mains on a tennis racket with a flying clamp

Take a look at this instructional video and learn how to start your mains on your tennis racket with a flying clamp, but without the double pull. This isn't a perfect replacement to starting with a starting clamp, but it's close. Hope everyone could follow along. Didn't have t ...more

How To : Clamp and glue a wobbly chair

Learn how to repair a broken or loose joint on your chairs or other furniture for long-lasting stability. Chairs take a real beating over time and it's only natural that over time one of those glue joints is going to fail. What do you need? Well to start with you need some com ...more

How To : Suture using a needle driver clamp

This video illustrate us how to suture using a needle driver clamp. Here are the following steps: Step 1: First of all take a clamp and fasten it on the book. Step 2: now take the suture needle and hold the thread through the thread holding needle and then form a knot in a s ...more

News : Shoot Anamorphic with a Clamp?

Here is a Philip Bloom Meet Up in Key West where they spent the day shooting Anamorphic, with an anamorphic clamp. I don't think this video looks that great, but Im not sure if its the clamp or the lenses they used in the clamp. The Anamorphic Clamp available for $75 USD at vi ...more

How To : Connect a toggle clamp

One important part of jewelery making involves completing toggle clamps. This jewelry how-to video demonstrates the proper way to connect a toggle clamp. Begin by holding one piece of the toggle securely in each hand. Push the bar through the circle part of the toggle, this co ...more

How To : Use the ATW on your tennis racket w/ no starting clamp

Check out this instructional video and learn how to use a generic around the world pattern on your tennis racket. This stringing pattern does not require a starting clamp. Once your mains are done, you'll want to count your crosses and you can determine where to go from there.

How To : Glue and clamp woodworking projects

In this woodworking tutorial, you'll be finding out how to properly glue and clamp woodworking projects. This is an important tutorial since some projects require the use of glue more than nails or screws. So it's important to know what to exactly do when working with both pro ...more

How To : Remove self retaining air duct clamps on a Saturn

When working on your car, it's always important to know how things work and what can be removed. If you can remove a certain part easily, in order to get to another part, it makes the day much easier. So in this tutorial, you'll be finding out how to remove the self retaining ...more

How To : Make a DIY Cold Air Intake

Instead of paying hundreds of dollars for a cold air intake, make your own version for your car. Cold air intakes can free up about 4 horsepower to the wheels, increase fuel economy, increase torque and make your engine sound better. All you need is a mass airflow sensor adapt ...more

How To : Make a Hyperbolic Paraboloid Using Skewers

In Monday's post, we created a sliceform model of a hyperbolic paraboloid. In today's post, we will create a similar model using skewers. The hyperbolic paraboloid is a ruled surface, which means that you can create it using only straight lines even though it is curved. In fac ...more

How To : Make a 4-Element Table with PVC Pipe

Now, I know what you're thinking... "I need an extra sexy coffee table that is like no other." OK, Maybe not. Maybe you're thinking, "I need a conversation starter that doesn't have to do with economic injustice, Left/Right political paradigms or health insurance. I need it ...more

DIY Plastination : Turning Dead Animals Into Science-Jerky

If you found the world renown Body Worlds exhibition gnarly and perverse, perhaps you'll find this latest parade of plastination a little less so—considering we don't share the same DNA as these specimens of jerky-in-the-name-of-science. The Koerperwelten der Tiere—or Animal B ...more

How To : Remove a fiberglass shower pan

To remove a fiberglass shower pan you will want to start by removing excess water in the drainpipe. Take a turkey baster and put it down in the drainpipe to siphon out the water. Use a knife and cut along the edge of the fiberglass panel where it meets the linoleum. Put a rag ...more

How To : Make a Sonobe Jasmine Dodecahedron

Math Craft admin Cory Poole posted instructions on How to Make a Cube, Octahedron & Icosahedron from Sonobe Units, plus some great complex models in his article, How to Make a Truncated Icosahedron, Pentakis Dodecahedron & More. These models use the standard sonobe unit and a ...more

How To : Make a wooden fingerboard

If you're into fingerboarding, then you're going to want to watch this video tutorial to see how to improve your fingerboard skills. Watch to learn how to make a wooden fingerboard. With just a few materials, your finger-skateboard will be up and running in no time. Supplies: ...more

Build a Home Arcade Machine : Part 2

I assume at this point you have already completed your control panel using Part 1 of this How To guide. Now, if you are anything like me, you couldn't fight the urge to play, and you have your panel sitting on saw horses in the living room. Depending on your situation, your s ...more

How To : Build a beer bong

Beer bongs are simple to make, and it's not difficult to make them even more user friendly. You will need a funnel, a valve, a tube, and clamps. Watch this video bartending tutorial and learn how to make a beer bong.

How To : Remove the inner tie rod end on an automobile

Richpin demonstrates how to remove the inner tie rod end on an automobile. First, get the car up in the air and support it by jack stands. Remove the wheel assembly. Loosen the outer tie rod end next to the steering knuckle. Loosen the jam nut. Then remove the nut that secures ...more

How To : Build a pot fountain

Nothing is more relaxing than the sound of moving water in the garden. Here's how to build a one-of-a-kind water feature in a weekend. How to: Step 1: Plumb the pot For this step, you'll need your decorative pot, a 1 3/4" by 1" barb fitting, a 1 3/4" PVC female adapter, plumb ...more

How To : Make a Toilet Paper Launcher

Shoot streams of toilet paper in midair with this ultimate TP machine, the Streamerator. Take a look at this instructional video and learn how to make a toilet paper launcher with a generic, electric yard blower. This gadget is extremely easy to make. First, you need a steel r ...more

How To : Silk screen print t-shirts in four minutes

This video, which was made at Peopleprint Community Media in Rochdale, teaches how to easily silk screen print a t-shirt in only four minutes! First, design the artwork to be used for the print, then print it on acetate. Next find a clean screen. Put some emulsion in a coating ...more

How To : DIY Pedal-Powered Phone Charger for Your Bike

Being healthy and active will help you live longer, but finding the strength to work out? That's hard. What does it do for me right now? I mean, here I sit, writing this article, thinking about going for a run, and I feel good just for thinking about running. But will I do it? ...more

How To : Install an exhaust on a Ford F150

In this Autos, Motorcycles & Planes video tutorial you will learn how to install a Borla exhaust on a Ford F150. For this you will need a 15mm and a 10mm wrench, a 15mm deep socket, a 10mm standard socket, a ratchet, safety goggles and work gloves. First remove the spare tire ...more

How To : Build Your Own Strawberry Tower

This article details the step-by-step instructions on how you can make a strawberry tower that can be used for your hydroponics/aquaponics system. The water dripping through the system contains the nutrients, so soil is not used. The growing media is expanded shale, but you co ...more

How To : Make your own affordable underwater camera rig

Want to film underwater, but can't afford the expensive professional camera rig? This tutorial shows you how you can construct your own functional underwater camera rig for about sixty dollars. You will need: small ankle weights, threaded seal tape, waterproof sealant, Velcro, ...more

How To : Build a Rustic Timber Table

These three videos will show you how to build a rustic, distressed kitchen table. I'll be walking you through the process of selecting some recycled timber from a junk pile, and with a little care and some simple joinery techniques, transform that waste timber into a distresse ...more

How To : Replace and install an exterior door with Lowe's

To replace a door, refer to Lowe's do-it-yourself for a step by step guide. Replacement is not very difficult. To replace just the door, tools and material required are: a new door, hammer, screw driver, tape measure, pencil, combination square, saw horses, clamps, chisel, a d ...more

How To Live Underwater : A Nevada Family's Bubble Fort

Would you rather live far up in the trees? Or deep underwater? A Nevada family of scuba divers have built the ultimate childhood getaway: the Needham family's "Bubble Room" is an underwater fort that sits at the bottom of a lake in the Sierras. The room is an air-filled pocke ...more

How To : Modify the PCV on a Kawasaki KLR650

This motorcycle tutorial shows you how to do a PCV mod on a Kawasaki KLR650. The PCV mod is putting a one way valve in the breather hose from the engine into the airbox. Purpose: only lets the engine case exhale, not suck air back in. Side effect: potentially reduces or elimin ...more

How To : Repair a wooden chair

In this video series, learn how to fix a broken piece of furniture you may have kept for years. Our expert will guide you step-by-step through a wood chair repair. Learn how to remove broken spindles and replace them with wooden dowels. Tips include using an epoxy glue, drilli ...more

How To : Make an indoor 3 story beer bong

In this episode of "Pimp My Crib - Campus Cribs" we will be examining how to give your 'Pad' a nice little touch up that everyone can enjoy, a lot. We will be making a 3 story tall beer bong. You will need the following items: A piece of string, about 20 feet of tube, a funnel ...more

EXPERIBASS : Violin+Viola+Cello+Double Bass

Diego Stocco is back (previously, the incredible Music From a Tree). This time Stocco has created the experibass: "Few weeks ago I visited a luthier looking for instruments parts, I had an idea in mind for an instrument I wanted to build. My curiosity was to hear the sound of ...more

How To : Build a personal weather machine

Plug this baby into your FiOS-powered computer and simulate the real-time climate of any location in the country -- rain, lightning, fog, sunshine. Get creative -- got any new weather effects you've figured out how to add to your Personal Weather Machine? We'd love to hear ab ...more

Prev Page
  • Hot
  • Latest