Tim Carter, of Ask the Builder, demonstrates tips you should know before installing ceramic tile over plywood or OSB. Following these tips will make your looking sharp and beautiful, and practical.
Considering installing hard wood floors? We recommend you watch this video first. Westhollow Floors talks about the various wood choices available, benefits and limitations of each one, and what you need to consider before you start. These guys take you through everything you ...more
This Lowe's video shows you how add warmth and beauty to your home by installing hardwood floors step by step. First you must prepare the sub-floor. You will need engineered hardwood planks, transitions, and moldings. You will also need flooring adhesive, trowel, hardwood floo ...more
Redoing your floors can be expensive unless you know how to do it yourself. Learn the basics for installing a new engineered wood floor in this how to video. Watch the short DIY show clip and follow along so that you too can install a new engineered floor in your kitchen.
This video shows you how to install a hardwood floor over concrete. You will need a plywood base. This video demonstrates the nail down method. You will need 15 nails per 8 feet by 4 feet sheet; plan according. The entire process is very easy and gives you easy steps to follow ...more
Woven Shades are not just stylish and chic, but Eco-friendly made from renewable materials great for Mother Earth! Installing Woven Wood Shades Watch the video above for a step-by-step tutorial on how to install chic woven wood shades to complement any window in the home.
In this video Henry shows you how to finish all the exterior trim on the shed. This video includes lot of tips to make the finish carpentry in this video easy and accurate. Video: .
I assume at this point you have already completed your control panel using Part 1 of this How To guide. Now, if you are anything like me, you couldn't fight the urge to play, and you have your panel sitting on saw horses in the living room. Depending on your situation, your s ...more
This article will show you how to make a shutter release cable for a Canon camera. It took me about half an hour once all of my materials were gathered. I came in at a total of about eight dollars. It has three switches and buttons. The black button on mine triggers the auto f ...more
Remember the arcades? Were you saddened when they closed up one by one, leaving no outlet to actually go out and socialize while you played video games? With all the home consoles and internet connectivity, gaming has evolved, but the social factor has been eliminated. Sure we ...more
It's that time a year when winter storms begin causing havoc across the United States, and when "rotating outages" are common to help sustain the electrical grid during intense cold periods. That means pretty much anybody with snow and ice in their backyard can succumb to powe ...more
When it comes to fence-building, nobody knows better than Lowe's. And if you're thinking about fencing an area of your home, either for privacy, decoration or busywork, this video series will inform you on everything you need to know. Learn how to choose and plan out your fenc ...more
If you've been thinking about installing a new deck on your house, but aren't sure where to begin, you've come to the right place. This video will show you how to install decking and lay deck boards. It doesn't go into too great of detail, but the tips they provide are invalua ...more
If you've been working on a project and need to know how to put up a door using a butt hinge, this video should help. In the tutorial, The Wood Whisperer, will let you know what tools you'll need to determine how to properly install a butt hinge mortise. Installing it incorrec ...more
Many home that have stairs in them, tend to have either wood or metal stair railings. Each has their own benefits, but metal tends to be cold and less attractive to homeowners and potential home buyers. Installing a wood stair railing adds much more character to the space and ...more
Maybe you just bought a new home. Maybe you've lived in your house for years. But if your deck looks like it's seen better day and needs an update to whip it back in shape, that doesn't necessarily mean you have to tear down and replace it. This two-part video from Lowe's wil ...more
As your home ages, so does your deck in the backyard, but there are ways to resolve this issue. If that wooden deck is looking weathered or worn, you can simply replace the components with composite materials without a complete rebuild. Composite doesn't splinter or have knots ...more
Part of the process is to create plans to follow when making the cabinet for the arcade game. when cutting the wood you need to allow for the 1/8th of an inch that the band saw will be cutting. You will also need a piece of plexi glass to give the game an authentic feel, spray ...more
Watch this video from This Old House to learn how to install landscape steps. Steps: 1 Drive 1x2 stake into ground, then use straightedge and level to find height of top step; mark height on stake. 2 Use level to find height of grade at bottom; mark height on stake. 3 Measure ...more
If you're not an everyday woodworker, then building a deck may be a challenge for you. But it's not as hard as it might seem. If you follow all of the required steps for deck building, you'll have one of the best ones on the block, and be pretty darn proud of it, too! So, che ...more
There can be areas of preparation you may not have anticipated before you start your project of installing your laminate flooring. Concrete Preparation If you are installing your laminate flooring over a concrete slab, you may not notice until you remove the old carpet that ...more
Installing Laminate Flooring on Stairs Laminate flooring can be installed on a flight of stairs, and this process can also be used when installing laminate on a floor and having to drop down a step to a sunken room. I will describe how to prepare and install laminate floorin ...more
Installing a T Mold Transition Between Laminate and Ceramic Tile There are several different types of laminate transitions that you may need when installing laminate flooring. Each one is used specifically for where the laminate flooring ends, such as where the laminate stops ...more
If you're looking to dress up an ordinary room, think about installing crown molding (also spelled moulding). Very few additions make a visual impact like crown molding, which gives a subtle yet elegant design element to any space. And with the proper tools and set up, install ...more
There are fewer things finer in a home than a hardwood flooring. For the do-it-yourselfer, however, it can be a fun, yet daunting task. Installing a hardwood floor can best be described as a combination of rough and fine carpentry. Pounding the nails home and bending warped fl ...more
Want to lay a hardwood floor yourself? It's easy. Provided, that is, you have all of the following materials: wood panels (preferably with built-in foam underlay), plastic sheeting, duct tape, tapping blocks, a hammer, a crowbar, a straight edge, a miter square, a pencil, stri ...more
Make a DIY wood sanding block for smooth surfacing with help from this video tutorial hosted by the can-do man, Ron Hazleton. Ron Hazleton is a DIY home improvement master. Everything from installing ceiling fans, to replacing toilets, to patching holes in your walls... If it ...more
Tim Carter, of Ask the Builder, demonstrates how to use solid-wood beaded ceiling planks to make a wood ceiling for your house. It is important to prestain and urethane the wood before it is installed.
I'm starting a laminate tile installation next Thursday. I thought I will show what is involved from start to finish. It's going in a kitchen and two bathrooms. There is ceramic tile in these rooms now and I'm installing the laminate tile right over the ceramic tile. The probl ...more
Lowe's home improvement expert Mike Kraft is back again to show to help us install laminate wood flooring in our homes. It has been assumed that proper sub-floor preparation has been done. All the tools, equipment, and materials are gone over in detail for your safety. Proper ...more
This video tutorial shows you the proper way to prepare for the installation of laminate flooring. One thing you need to do is maintain a temperature of a minimum of 65 degrees. You can install it practically anywhere, as long as there is no moisture or dampness. Concrete, cer ...more
Not sure how to safely clean your wood table without ruining it? In this video tutorial, learn how to properly wipe off your table and how to protect it with a sealant called, Pastewax. This substance dries and does not attract dust making your table look shiny & new, like a p ...more
Want to create a realistic or customized wood stain for your home? Learn how to get the exact color stain you need to match existing wood finishes or to create unique effects. Ron Hazleton is a DIY home improvement master. Everything from installing ceiling fans, to replacing ...more
Many spend a good amount on outdoor furniture... only to see it get ruined by the effects of weather or residue. In this video hosted by Ron Hazleton, learn how to restore and preserve outdoor furniture by cleaning, sanding and applying a stain and wood sealer to protect the w ...more
When installing baseboards, crown molding ("moulding") and chair rails, it's tempting to cut 45-degree miters at the corners and hope for a sure fit. The problem is that most walls aren't square. Joining two 45-cut molding pieces may give you a square joint, but a square joint ...more
Vinyl wall base molding is an easy-to-install substitute for wood baseboard molding. In areas that you have installed a vinyl or carpeted floor, vinyl wall base molding is a very decorative and functional option for surrounding the room perimeter. You have several color choice ...more
This laminate flooring is very impressive as far as the surface is concerned. My client actually used a sharp screw and tried to scratch it, and we could not see anything. It is rated as a AC3 which is mid grade as the grading system is from AC1 to AC 5, 5 being the best. I h ...more
Home accidents. It's up to you to protect your family… your children… from accidents in the home. And there's one place that seems to get the most attention when dealing with safety concerns… The kitchen is one of the busiest, most accident-prone rooms in the house. Design a k ...more
Josh Copp and Madeline Donahue show us how to build a light table from pine wood and plywood utilizing two fluorescent light fixtures as the light source inside the box. The frame of the box is fashioned out of two 1X8 planks cut into four pieces so that two sides are 30 inche ...more
This video will show you how to drill a clean hole in ceramic, porcelain, clay, glass or tile. Materials needed for this project are: carbide tile bit, normal variable speed drill (not a hammer drill), air tool oil, plumbers putty, MDF board or a scrap piece of wood. Step 1 - ...more
Eagle Lake Woodworking, hosted by John Nixon, offers great do-it-yourself guides for building your own furniture, especially in the American Arts and Crafts style, and turning your garage into an amateur woodshop. Search Eagle Lake on WonderHowTo for more carpentry tutorial vi ...more
Have a new door that needs installed? Well, first thing you're going to have to do is remove the old one! Check out this home improvement video tutorial on how to completely remove an interior door in your home. This are easy to follow instructions, and you only need a few si ...more
Soldering copper pipes is a basic plumbing skill that once mastered will enable you to tackle many DIY home repair and home improvement projects - for instance, replacing copper water lines or installing a new spigot. It can be as much an art as it is a science, thus the more ...more
Tim Carter demonstrates how to remove insulated glass panels from either side of a front door. Replacing the sidelights on the front door is possible. Just follow these steps for glass replacement. If the insulated sidelight glass panel on your front door goes bad, it can be ...more
A CNC router machine is probably the most useful tool a hobbyist can own, but the price for a CNC machine on the market is way more than the average hobbyist is willing to spend. You can build your own CNC with very basic tools, little knowledge of machinery, mechanics, or ele ...more
If you want to install laminate flooring on your stairs I would recommend that you do a lot of research and find the information you will need to do it correctly. Installing laminate flooring on stairs can be tedious and time consuming and is a lot different than installing la ...more
Don't let that stuck drawer aggravate you on a daily basis; find the problem and fix it once and for all. Step 1: Remove the drawer Remove the drawer. Pull it out until it stops, then lift up the end and pull it a little bit more. This should release the drawer from its glid ...more
Instead of pushing, pulling, and cursing, why not fix that door that sticks? You Will Need * A screwdriver * Some cardboard * Screws that are larger than those in the hinges * A pencil * A belt sander or sanding block * A book or piece of wood * A solid wooden block Step 1. ...more
Periodically, motorcycle and ATV exhaust system can be rebuilt to maintain the proper performance and sound level expected from the exhaust system. My experience was with a dirt bike that had an aftermarket high performance exhaust installed.I bought my 99 XR400 second hand an ...more
Watch this video from This Old House to learn how to install attic stairs. Steps: 1. Mark rough opening of new fold-down staircase on the ceiling joists in the attic. 2. Use a reciprocating saw to cut joists and nails holding any joists that must be removed. 3. Cut around cei ...more
No one likes having their home invaded, and sometimes you just don't want to have to wait those precious few seconds for someone or something to drown, suffocate, or burn up. This trap utilizes gravity to destroy anyone who may want to pillage your home, be they monster or pla ...more
Just how private is your Facebook profile? To some extent, that's up to you. Many Facebook users share and poke their days away, never knowing about the plethora of custom privacy settings that lie just a click away. Facebook's privacy menus can look a little complicated to th ...more
People ask me all the time, "Nick, what are the best blinds for my home in terms of Wood vs. Faux Wood?" Well the answer to that question is not so cut and dry. However, I can help steer you in the right direction. In this post, we will examine the pros and cons of both wood a ...more
If you already have basic faux wood ceiling beams installed in your home, then you may still want to go a bit further, and suspended faux wood beams is the way to go. It's decorative, cheaper than real wood, lightweight and can add character and warmth to a plain room. This vi ...more
Just because you have a cathedral ceiling in your home, doesn't mean you can't enjoy the beautiful decorative texture of wood beams. Faux wood ceiling beams are a great way to add character and warmth to a plain room. Compared to real wood, they're cheaper, lightweight and eas ...more
Let's face it— we'd all like to have some decorative wooden beams on our ceilings in our living rooms. It's a great way to add character and warmth to a plain room. But you don't need real wood to get this look. There's a lightweight and cheaper alternative— faux wood ceiling ...more
Walls don’t last forever, be prepared. Building a house from scratch, a room add on or if it’s just time to turn one room into two you will need to make a sturdy wall frame to ensure the proper construction of your new wall. Reinvent your living space by installing a new wall ...more
This video is an overview of all the videos in our DIY Shed Videos Series. Henry briefly goes over what you will learn in all 15 of our shed building videos. Video: . To get started, check out the following guides for building your shed. Part 1: Ground Preparation Part 2: Sel ...more
When you think about car customization, you think about installing a stereo or a turbocharger or something like that, but Joe Harmon and gang have gone a step further and built their own custom car - literally woven out of wood. The high-performance Splinter is made almost en ...more
Last year, Instructables user Horatius.Steam created Dr. Brain, a small computer connected to a model brain that can tell stories and have Skype conversations. But one thing it couldn't do was print, so to solve that problem, he came up with this awesome Steampunk "Ticker Mach ...more