Install a Blow of Valve

How To : Install a Blow Off Valve

In this episode the Mighty Car Mod team shows you how to install a blow off valve. NOTE: make sure you have the right pipe or connections from the new BOV to your motor type - otherwise welding may be required.

How To : Install a shower valve

Watch as an expert plumber demonstrates how to replace shower valves in this free online video about home repair. Part 1 of 12 - How to Install a shower valve. Install a shower valve - Part 2 of 12. Click through to watch this video on ehow.com Install a shower valve - Part 3 ...more

How To : Install an air valve for hot-water heating system

Watch this video from This Old House to learn how to install an air valve for a hot-water heating system. Steps: 1. Turn off water leading to the boiler. 2. Mark the pipe for cutting, which allows the installation of the air valve. 3. Use reciprocating saw to cut out section ...more

How To : Install a sprinkler valve box

Installing a sprinkler valve box can be made easier by using bricks to support the valve box and using crushed rock in the bottom to make it look a little neater. Check out this video tutorial to see how to install a sprinkler valve box with help from Sprinkler Daddy. This is ...more

How To : Install an automatic fill valve

Having a beautiful waterfall in your outside area, is a great way to add a relaxing feature to your landscape. But a common problem with them is that during the long hot summer months, water tends to evaporate and this causes the water in waterfalls and ponds to dissapear. So ...more

How To : Install an airless water valve

This video shows you how to set up the Airless Water Valve. Installing the airless water valve can save you 20-40% on your water bill. Visit Airless Water Valve for more information

How To : Install or move a shower valve

This two part video show you how to remove an old shower valve, preparation and installation of a new shower valve. Also, you'll see how to clean, cut and connect copper plumbing pipes. Don't forget to watch part two and always make sure to shut off the water main first! Part ...more

How To : Install a toilet water inlet valve

In this video we learn how to install a toilet water inlet valve. First, turn the water off and flush the toilet to get rid of the water in the system. From here, pull out the flush valve by turning it clockwise and lifting it. Then, grab your new valve and replace it where th ...more

How To : Install a water heater shut off valve

Watch this video from This Old House to learn how to install an automatic shut off valve for a water heater. Steps: 1 Turn off the water to the water heater. 2 Drain the water heater using an electric pump and garden hose. 3 Shut off the gas, then disconnect the gas line from ...more

How To : Install an ice-maker or water dispenser valve

Maybe your fridge is old-fashioned or the old ice-maker or water dispenser just broke. Don't buy a whole new fridge, or pay for expensive repairs. With some help from this how-to video, you can do it yourself. Watch this video tutorial and learn how to install and ice-maker or ...more

How To : Install a radiator thermostat with This Old House

Watch this video from This Old House to learn how to install a radiator thermostat. Steps: 1 Close the valve at base of radiator. 2 Turn off the room's thermostat. 3 Carefully unscrew the existing air vent from side of radiator. 4 Put Teflon tape on threads of new thermostati ...more

How To : Build and outdoor couch

This is a video tutorial describing how to build an outdoor couch for your porch. First measure out where you want to put your outdoor couch onto your porch. Then start building the first post. You should use concrete block to build this post. Then build out from the post the ...more

How To : Make an airsoft machine gun at home

First of all you need medicine bottle, a big pen, some peewee. In case you wish you can also use a compressor fitted with a ball valve throttle. Now take the medicine bottle and make two holes of 1/4 inches into both ends. Once you have done this, you shall get cap with a hole ...more

How To : Make clouds inside a bottle

Using a huge jar and with water colored with die in it you can make clouds. To do this set up the apparatus as shown in the video. Now open up the top valve and blow air into the jar. Now this causes the air inside to be compressed as we are pushing more air into the confined ...more

How To : Use a Hydroponic Seed Starter to produce seedlings

Learn how to make and use a hydroponic seed starter to produce seedlings with this video tutorial. This is a very easy setup to make. Start with a basic metal shelving unit. Hang florescent lights above each of the shelves on the shelving unit. Make sure the lights are balance ...more

How To : Fix a sweating toilet tank with This Old House

Watch this video from This Old House to learn how to fix a sweating toilet. Steps: 1. Turn off water and drain the pipes. 2. Cut a tee-fitting into a nearby hot-water water pipe. 3. Dry-assemble the various copper pipes and fittings to the anti-sweat valve. 4. Solder together ...more

How To : Build a waterfall using retaining wall block

The procedure was adopted to build a waterfall in Oregon Coast Garden Center, Wald-port. 1. A level pad was cut to arrange the first row of blocks 2. 3 rows of retaining wall block was set in the desired shape. 3. The inside of the structure is covered with landscape fabric fo ...more

How To : Detect an air leak in a Nitro RC engine

In this tutorial, we learn how to detect an air leak in a Nitro RC engine. Air leaks damage your engine which will take your tuning and completely void it. Now, take some soapy water and apply it to your engine and anything that is connected in between. Block off one end of th ...more

How To : Install a new chain on a Ducati Monster S2R

See how to install, rivet and tension a new chain on a Ducati Monster S2R. This video applies to all 2 Valve Ducatis. Part 1 of 2 - How to Install a new chain on a Ducati Monster S2R. Part 2 of 2 - How to Install a new chain on a Ducati Monster S2R.

How To : Change a bicycle tire & replace the inner tube

In this tutorial, we learn how to change a bicycle tire & replace the inner tube. First, take the wheel off of the bike. Then, see if you can find any holes on the outside of the tire. Then, remove all air from the tire tube and remove 1 side of the tire using tire levers. Aft ...more

How To : Fix a running toilet with This Old House

Watch this video from This Old House to learn how to fix a running toilet. Steps: 1 Turn off the water at toilet's shut-off valve. 2 Remove the rubber flapper from flush valve inside the tank. 3 Inspect flapper for damage or discoloration. 4 Check location of float on chain; ...more

How To : Install a frost-free sillcock

If you live in a colder climate, your water pipes may be susceptible to freezing. For the most part, your plumbing is safely inside the heated living space of your house. However, a sillcock (spigot) on the outside wall of your house is exposed to the elements and can freeze d ...more

How To : Install radiant heat with This Old House

Watch this video from This Old House to learn how to install radiant heat. Steps: 1. Screw aluminum transfer plates to underside of subfloor; install two plates per joist bay. 2. Assemble radiant-heat manifold with circulating pump, sensor, relay switch and mixing valve. 3. C ...more

How To : Install an instantaneous water heater

Watch this video from This Old House to learn how to install an instantaneous water heater. Steps: 1 Use template to mark position of vent hole on exterior wall of basement. 2 Bore center pilot hole for vent using a 3/8-inch-diameter masonry bit. 3 Cut vent hole through wall u ...more

How To : Install a sprinkler system

In this video series, landscaping expert Fernando Chavez teaches how to install a sprinkler system. He teaches what tools and materials are needed, how to design a sprinkler system, how to maneuver around cement, corners, and curves, how to lay sod, how to install sprinkler he ...more

How To : Install addons in Garry's Mod

Garry's Mod is a sandbox providing tons of content to play with for Valve games. This game allows you to manipulate creatures and objects in popular games such as Half-Life 2 and Counter-Strike. AddOns in Garry's Mod will allow you to import your own models, vehicles, cities, ...more

How To : Run an ice maker supply line to a refrigerator

In this video, Karen Schmidt demonstrates how to hook up a water supply to a refrigerator where none exists. For this tutorial you will need the following tools and supplies: an ice maker supply line, a tube cutter, a snap-in fitting, a half-inch by quarter-inch compression va ...more

How To : Refill an Air Duster Can with a Bicycle Pump

In this life hack video, I am going to show you how you can refill your air duster can with a bicycle pump. Video: . Step 1: Items Needed All you need is an empty air can, some liquid metal epoxy, and a tank valve similar to what is used on a bicycle tire. You will also need ...more

How To : Make a Super Cheap One-Way Check Valve

If you're going to build yourself a water gun to cool down this summer, or maybe just a useful water pump, you'll need some check valves. However, the most expensive parts of a water pump or DIY super soaker are usually the check valves. So, let's make some from scratch for as ...more

How To : Install blown-in insulation

Have you ever felt cold in your older home, even with the heat cranked? Ever feel drafts that seem to come from nowhere? And conversely, in the summer, is your home an oven? Many older houses are improperly insulated, if there is any insulation at all. This can have a large im ...more

How To : Install Ubuntu Linux on an HTC Evo 4G

Looking to make your HTC Evo 4G smartphone even better? Unlock your phone's full computational potential by installing Linux on it! This video guide presents a complete, step-by-step walkthrough of the process. For more information, and to get started installing the Ubuntu Lin ...more

How To : Modify gearing on a Traxxas Rustler R/C vehicle

If you're fond of remote-controlled vehicles, you might appreciate this video tutorial on how to modify gearing on a Traxxas Rustler R/C vehicle. The Traxxas Rustler is a proven favorite with a formula for rugged fun that nothing else can touch. The Rustler blows the doors off ...more

How To : Install a XAMPP testing server on a PC

If you have a website or do any type of web development you have probably needed a server at some point. Not everybody has a full blown commercial web server at their disposal for development, experimenting, and testing their site, so try this solution: an XAMPP open source bu ...more

How To : Replace an old kitchen faucet with a new one

Replacing old kitchen faucets can be a great way to adding a new item that can be used to maximize your cleaning and cooking needs. This video tutorial shows you what it takes to replace an old existing kitchen faucet with a new one. It will also show you how to install shut-o ...more

How To : Install a car security killswitch

A killswitch is exactly what you think it is: A switch that kills an operation in an emergency situation when the operation can't be shut down in the usual manner. It shuts your operation no matter what the consequences. You can actually craft a car security killswitch to pre ...more

How To : Install No-Frills Drip Irrigation

Solving a Dilemma This is a simple how-to for a cost effective drip irrigation system for your garden. My motivation to set up my garden for drip irrigation was pretty simple. In the summer, it gets to 90+ degrees outside, and my 50’ garden hose didn’t reach the far extents w ...more

How To : Install a towel warmer with This Old House

Watch this video from This Old House to learn how to install a towel warmer. Steps: 1. Drain hot-water heating system; turn off water supply to the old radiator. 2. Use reciprocating saw to cut hot-water supply and return lines from old radiator; remove radiator. 3. Cut open ...more

How To : Install a full glass backsplash in your kitchen

Installing a backsplash in your kitchen is a great way to add a certain sense of style to the space. It can also prevent any kind of stains of taking place on the walls as well and it's easy to clean up. With this tutorial from the DIY Network, you'll find out about full glas ...more

How To : Attach automatic sprinkler valves

Check out this video tutorial to see how to attach automatic sprinkler valves. These tips on installing your own automatic sprinkler valves from Sprinkler Daddy will help your lawn turn into luxurious green grass, preventing any further landscaping needs. A little bit of water ...more

How To : Install a dishwasher

In this video, we learn how to install a dishwasher. First, take out your directions from the package and throw away the rest of the packaging. Also, discard your old dishwasher if you don't need it. Next, attach the PVC hose to the water supply, making sure it's turned off, t ...more

How To : Install a lawn irrigation system

In this how-to video, you will learn how to install a lawn irrigation system. You must have a digital controller with an AV program. This controls the zones at which the water comes on. These can save you a lot on water use. The controller controls the valve which accesses the ...more

How To : Change a road bike tire

This how-to video demonstrates how to change the tire of a road bike. First of all, the old tube must be removed with the help of some tire levers. The new tube that will fit the rim must be inflated at an optimal 5 psi. The tube will then be mounted on the rim starting with t ...more

How To : Remove and replace a toilet

Changing a toilet is really not the dirty and difficult job that you would imagine. Start by turning the water off using the valve that is located on the wall. Empty the tank by flushing the toilet and holding up the drain valve. Soak up the excess water with a sponge. Disconn ...more

How To : Install a glass vessel sink or countertop

This video tutorial shows you how to install a glass vessel sink or countertop. First you need to make sure that the glass vessel sink or countertop has all of the pieces needed and that none of the pieces are scratched or broken. You then need to place the mouthing ring on th ...more

How To : Maintain the Tippmann A-5 power tube and valve

In this how-to video, you will learn how to maintain a Tippman A-5 Power Tube and Valve. First, pull the valve out of the power tube. Grab the pin with a pair of pliers and give it a firm yank. Next, remove the o-ring and set it aside. Remove the other o-ring off the back. A w ...more

How To : Blow-up and remove a large rock from the ground

Is there a rock in your yard that's bothering you? This video will show you how to get rid of it. First you dig around the rock to figure out where you want to drill your holes. Then you drill holes into the sides of the rock. It’s important to clean the dust out of the holes ...more

Prev Page
  • Hot
  • Latest