Install P-pipe

How To : Use funny pipe when installing a sprinkler system

Installing a sprinkler system in your yard is a great way to spread water to all your plants and yard. All you need to do is turn a switch or knob and instant water. So if you're planning on installing a sprinkler system in your yard, it's important to know what each item can ...more

How To : Install drain pipes

In this DIY tutorial, Joe Schmidt demonstrates how to install a drain system. He then explains different ways to configure the drain system for your own situation. Why hire a professional to install your drain pipes when you can do it yourself with this how to video?

How To : Make your own solid pipe clamp hold-down

In this video "A better way" presenter Chuck Miller demonstrates a method of how to create a job site pipe holder (clamp hold-down) as opposed to a c-clamp, bar clamp or blocks of wood. It involves use of a pipe flange of the same diameter as the pipe being held. It shows you ...more

How To : Install a utility sink with This Old House

Watch this video from This Old House to learn how to install a utility sink. Steps: 1. Turn off water 2. Cut section from existing drain pipe and install a new Wye-fitting 3. Assemble PVC pipe and fittings for new drain/vent system 4. Glue drain/vent system to existing vent s ...more

How To : Install or move a shower valve

This two part video show you how to remove an old shower valve, preparation and installation of a new shower valve. Also, you'll see how to clean, cut and connect copper plumbing pipes. Don't forget to watch part two and always make sure to shut off the water main first! Part ...more

How To : Install a gas fireplace with This Old House

Watch this video from This Old House to learn how to install a gas fireplace. Steps: 1 Prepare installation site by building wall recess to accept fireplace. 2 Cut hole through exterior house wall and install stovepipe thimble. 3 Attach short section of stovepipe to exhaust p ...more

How To : Install a Blow Off Valve

In this episode the Mighty Car Mod team shows you how to install a blow off valve. NOTE: make sure you have the right pipe or connections from the new BOV to your motor type - otherwise welding may be required.

How To : Build a pot fountain

Nothing is more relaxing than the sound of moving water in the garden. Here's how to build a one-of-a-kind water feature in a weekend. How to: Step 1: Plumb the pot For this step, you'll need your decorative pot, a 1 3/4" by 1" barb fitting, a 1 3/4" PVC female adapter, plumb ...more

How To : Vent a bathroom fan with This Old House

Watch this video from This Old House to learn how to vent a bathroom fan. Steps:1. Screw the humidifier to a wall near the furnace. 2. Cut away insulation from the duct using a utility knife. 3. Position the hole-cutting template onto side of duct. 4. Drill pilot hole through ...more

How To : Install a drip irrigation watering system

Check out this landscaping video tutorial to see how to install a drip irrigation watering system. You'll need this if you want to keep your garden looking great. You will have to poke a hole in the pipe for every shrub. Then, you'll need to install a coupler. This drip irriga ...more

How To : Install a water heater shut off valve

Watch this video from This Old House to learn how to install an automatic shut off valve for a water heater. Steps: 1 Turn off the water to the water heater. 2 Drain the water heater using an electric pump and garden hose. 3 Shut off the gas, then disconnect the gas line from ...more

How To : Install KronoSwiss laminate flooring

While remodeling or redoing a room, many owners will inevitably want to install laminate flooring. This video shows how to install laminate flooring beginning with what tools and supplies will be necessary and then showing panel-by-panel how to install each floor panel. It als ...more

How To : Install a recycling chute in your kitchen

Finding room in the kitchen to store the various bins needed for recycling can take up a lot of valuable cabinet space. Here Danny comes up with an innovative solution to the problem by installing chutes made from standard 4” dryer vent pipe that send cans and plastic bottles ...more

How To : Install a frost proof faucet with This Old House

Watch this video from This Old House to learn how to install a frost proof faucet. Steps: 1. Turn off the water and drain the old hose faucet, also called the sillcock. 2. Use emery cloth to clean the copper water pipe leading to the hose faucet. 3. Cut the pipe using a tubin ...more

How To : Install an air valve for hot-water heating system

Watch this video from This Old House to learn how to install an air valve for a hot-water heating system. Steps: 1. Turn off water leading to the boiler. 2. Mark the pipe for cutting, which allows the installation of the air valve. 3. Use reciprocating saw to cut out section ...more

How To : Install a vanity and sink with Lowe's

In this video, we learn how to install a vanity and sink with Lowe's. A great way to give your bathroom a makeover is to give it a new vanity and sink. First, turn off the water from the water line, then take down the pipes from under the sink. Use a bucket to catch extra wate ...more

How To : Install a wall niche

A wall niche is a great way to add a nice decorative look to a wall. The niche is made of lightweight polyurethane. To install the niche choose the location on the wall where you want to put the niche. Put the niche up to the wall and draw an outline around it. Before you star ...more

How To : Install a sport bike Slip-On exhaust

Learn how to install a sport bike slip-on exhaust pipe in this free video series on motorcycle after market parts installation. Part 1 of 10 - How to Install a sport bike Slip-On exhaust. Install a sport bike Slip-On exhaust - Part 2 of 10. Click through to watch this video on ...more

How To : Install radiant heat with This Old House

Watch this video from This Old House to learn how to install radiant heat. Steps: 1. Screw aluminum transfer plates to underside of subfloor; install two plates per joist bay. 2. Assemble radiant-heat manifold with circulating pump, sensor, relay switch and mixing valve. 3. C ...more

How To : Install a washing machine pump

This home appliance tutorial details how to install a washing machine pump into a washing machine without one. The steps are roughly as follows: Plug in the pump connector. Replace the two retaining screws from underneath. Replace both pipes and spring washers. For a video wal ...more

How To : Install BuildCraft and IndustrialCraft

BuildCraft Mod enhances everything about fuel and making things run. Not only that thought, BuildCraft Mod adds new and awesome things inside it! Like all those pipes, quarries, and energy makers. Well all those things will help you enhance your same old Minecraft! Some Mods a ...more

How To : Upgrade your truck's exhaust system

Still got stock? Many factory installed exhaust systems not only sound anemic, they actually are because they scrub power. The designers who are given the task of producing these pipes are often handcuffed by several different requirements that add up to one big compromise. Ex ...more

How To : Install a frost-free sillcock

If you live in a colder climate, your water pipes may be susceptible to freezing. For the most part, your plumbing is safely inside the heated living space of your house. However, a sillcock (spigot) on the outside wall of your house is exposed to the elements and can freeze d ...more

How To : Install a sump pump with This Old House

Watch this video from This Old House to learn how to install a sump pump. Steps: 1 Set sump basin upside down on basement floor; mark its outline on floor. 2 Use demolition hammer to chop through concrete floor. 3 Dig hole deep enough to set basin flush with floor. 4 Wrap the ...more

How To : Install a towel warmer with This Old House

Watch this video from This Old House to learn how to install a towel warmer. Steps: 1. Drain hot-water heating system; turn off water supply to the old radiator. 2. Use reciprocating saw to cut hot-water supply and return lines from old radiator; remove radiator. 3. Cut open ...more

How To : Install an instantaneous water heater

Watch this video from This Old House to learn how to install an instantaneous water heater. Steps: 1 Use template to mark position of vent hole on exterior wall of basement. 2 Bore center pilot hole for vent using a 3/8-inch-diameter masonry bit. 3 Cut vent hole through wall u ...more

How To : Install a shower head

In this series of home improvement videos, expert engineer and licensed home inspector George A. Finn III guides you through the entire process of installing a new hand-held shower head. He shows you what tools you’ll need to get started and offers tips on planning the install ...more

How To : Replace and install a kitchen faucet with Lowe's

In this tutorial, we learn how to replace and install a kitchen faucet with Lowe's. Start out and check to see how many pipes you have underneath your faucet. After this, purchase your new faucet and all of the parts that go along with it. Once you have all of these, turn off ...more

How To : Install a dishwasher

In this video, we learn how to install a dishwasher. First, take out your directions from the package and throw away the rest of the packaging. Also, discard your old dishwasher if you don't need it. Next, attach the PVC hose to the water supply, making sure it's turned off, t ...more

How To : Install dual exhaust on your tractor

In this tutorial, we learn how to install dual exhaust on your tractor! First, find the exhaust strip on the tractor, then detach the muffler and slip the regular pipe into the muffler. After this, get a 3/4" pipe and slip it up into the other pipe and well around it. It shoul ...more

How To : Install an exhaust on a Ford F150

In this Autos, Motorcycles & Planes video tutorial you will learn how to install a Borla exhaust on a Ford F150. For this you will need a 15mm and a 10mm wrench, a 15mm deep socket, a 10mm standard socket, a ratchet, safety goggles and work gloves. First remove the spare tire ...more

How To : Encrypt files with OpenSSL in Debian Linux

This video shows how to encrypt files with OpenSSL in Debian Linux. First we check if open SSL is installed on the system. If not, install it using packet manager. Next create the file going to be encrypted. Now encrypt the file. In this case AES algorithm in ypher block chain ...more

How To : Install a toilet for your home

To install the new toilet you will need a putty knife, hacksaw, tape measure, adjustable wrench, level, sponge, and replacement wax seal. Before you begin removing the old toilet, turn off and disconnect the water supply to the toilet. Then flush the toilet to get the water ou ...more

How To : Install a shower head properly

Sometimes your old shower head just doesn't cut it anymore. Don't fret, installing a new one is a simple task. You Will Need * A cloth or rag * An adjustable wrench * Cleaning solution for calcium, lime, or rust deposits * A roll of plumber's tape * A replacement shower head ...more

How To : Repack a Motorcycle Muffler

Periodically, motorcycle and ATV exhaust system can be rebuilt to maintain the proper performance and sound level expected from the exhaust system. My experience was with a dirt bike that had an aftermarket high performance exhaust installed.I bought my 99 XR400 second hand an ...more

How To : Do a 16 inch layout on stud wall

Bob Schmidt from Home Remodel Workshop demonstrates how to frame a wall 16 inches on center. His tutorial is especially helpful, so pay attention to his tips, tricks, and specific techniques. When laying out a top and bottom plate for a typical wall a framing square is usuall ...more

How To : Solder copper pipes for plumbing

Soldering copper pipes is a basic plumbing skill that once mastered will enable you to tackle many DIY home repair and home improvement projects - for instance, replacing copper water lines or installing a new spigot. It can be as much an art as it is a science, thus the more ...more

How To : Straight pipe your small tractor engine

In this tutorial, we learn how to straight pipe your small tractor engine. First, insert a one inch screw pipe to your exhaust, then connect pipes into it so it connects to the back of the vehicle. You will need to install several elbow pipes as well as longer straight pipes. ...more

How To : Build a raised garden bed for sustainable living

Having a raised garden bed is great in the city because you can fill it with good soil and create a healthy environment for your plants. Install a hoop house made from PVC pipe. To build the raised bed, use 2x10x8 lumper. Predrill the holes at the corners to make it easier to ...more

How To : Install Dry Core basement sub floor

First, the plywood or oriented strand board (OSB) subfloor floats on a corrugated or “cleated” waterproof underlayment, so the wood never actually touches the floor. The underlayment material can be made of Styrofoam or heavy-duty polyethylene, the same material used in corrug ...more

How To : Replace washing machine hoses & why

This video explains to the viewer the advantages of replacing washing machine hoses. As well as, rather more importantly, explaining how to complete the process. According to the creator the rubber hoses that are standard to most washing machines are subjected to high pressure ...more

How To : Understand & use gutter guard

In this video you'll learn everything you need to have and how to use and understand your gutter guard. Tracy shows you all the different type of gutter guards, plastic, powder coated metal, galvanized mesh, the ridged mesh, and your hechhog piping. It takes you from everythin ...more

News : Three DIY Snow Vehicle BEASTS

As Popsci says, these DIY snow vehicles show winter who's boss. The Snow Chopper Two government employed mechanics in Antarctica built a "snow chopper" with junkyard parts and trash. The engine and track are from a totaled 1981 Ski-Doo Elan, and everything else from "savvy d ...more

How To : Build a retaining wall for your home

To create a retaining wall all you need to do is follow these simple steps. To begin you will need to get many interlocking wall blocks and either sand or concrete. The first step is to plot and measure the retaining wall's size and shape. Use your measurements to figure out t ...more

How To : Create a underground wire tunnel

Tim Carter of Ask the Builder, demonstrates how to drill a hole under a sidewalk, driveway or walkway so you can install an underground wire. If your project calls for running a small cable or wire under an existing patio, sidewalk or driveway, there is an easy way to do it, ...more

How To : Fix a sweating toilet tank with This Old House

Watch this video from This Old House to learn how to fix a sweating toilet. Steps: 1. Turn off water and drain the pipes. 2. Cut a tee-fitting into a nearby hot-water water pipe. 3. Dry-assemble the various copper pipes and fittings to the anti-sweat valve. 4. Solder together ...more

Prev Page
  • Hot
  • Latest