This video shows you how to sharpen a jack knife or wood-carving knife using coarse, medium, and fine stones and cooking oil. Use the coarse stone, applying oil to the stone first then pushing the knife down on the stone in each direction, matching the bevel to the stone. Next ...more
Balisong knives, or butterfly knives, are folding pocket knifes with two handles that can counter rotate. People love performing tricks with them because of the balisong butterfly knife's flipping ability. Since knives aren't toys, make your balisong butterfly knife out of Leg ...more
This video teaches the secrets to sharpen a convex wood carving knife in simple steps. First find out how dull your knife is by cutting a paper or shaving hair on you hands. Now take a sand paper attached to a pad and start sharpening the ends by applying less pressure. Now tr ...more
In this tutorial, we learn how to make a butter knife out of sycamore wood. First, you will take a log then you would split it in half. After this, cleave off a flap off of this. Next, take a knife to flatten it out. Take the width down so it isn't thick anymore. Use a knife t ...more
Videojug and Simon Eller of Bushcraft And Survival Skills Magazine team up in this informative video to demonstrate how to split wood with a knife or axe. Place your knife where you want to split the wood and use another reasonably heave piece of wood to strike the knife. Good ...more
In this three-part carving tutorial, Valerie Jones demonstrates her chip-carving techniques on Mahogany wood. Using an X-acto knife, she carves the wood by hand & describes how to carve German-style, geometric patterns into the wood after stenciling the pattern on the outer wo ...more
Changing your doors can instantly improve the look of your home, and yes, it is a job you can do yourself. It just takes a couple of hours, a lot of patience and this step by step video tutorial. Stop hanging around, watch this video on how to hang a door and get to it. Here' ...more
Grafting, also known as "top working," is simple-but-essential technique that enables you to change the variety of fruit a tree bears. In this tutorial, Stephen Hayes of Fruitwise Apples Heritage demonstrates the rind grafting technique, a useful method for grafting over a sou ...more
Forget surviving the wilderness— surviving the city is hard enough! This video talks about herbs, bushes, plants and trees that you can use in a survival situation in an urban environment. If you're down on your luck, forget about coins on the street corner and survive off you ...more
Grace Bonney shows us an easy way to create an upholstered headboard for your bed. Using a low-end easy budget, you will be able to create a elegant looking headboard using wood, foam, batting, fabric, scissors, a utility knife, a staple gun, and flush mounts. After cutting ou ...more
In this video tutorial, you'll learn how to make utensils in the wilderness. You'll see how to make a wooden fork, spoon, pot hanger and support when out in the woods. Also, learn how to clean your knife using moss. A nice piece of hazel wood is what you'll want for this survi ...more
This video demonstrates how to shell, devein, and butterfly shrimp. For this, you will need a paring knife or a pair of kitchen shears and large shrimp. Cut the shrimp along the back of the shrimp. Remove the shell. If you want to leave the tails on, then don’t cut through the ...more
It's no secret, artists are broke. That's why they're referred to as "starving artists". One day these artists will achieve unimaginable success, but for most of their lives, they'll be struggling to survive… struggling to keep their vision alive. That's why they need to work ...more
If you are in the wild and have nothing to do, just to play around with your knife , then you should surely watch this video. First, you have to find a knife. After that you must find a good branch or piece of wood that's the same size as a spear. After that you must take the ...more
Using guns in your independent films is risky business, and expensive to boot. Since you probably don't need to actually shoot anything, you can probably get by with a replica prop gun. If you're gonna do that, why not make it yourself? This video will show you how to make a r ...more
Preparation When creating a new lawn it is essential that the soil is prepared properly to ensure a satisfactory outcome when laying turf or sowing lawn seed. Whether you decide to lay turf or seed, the preparation is the same. This video shows how to prepare the soil ready f ...more
When that dusty old dresser you have starts looking more fit for Grandma than your sleek 21st century home, it may be time to refinish. This tutorial guides you accurately and quickly through how to refinish furniture, including using a chemical stripper, scraping off the fin ...more
I am writing this quick post in response to the recent earthquakes and tsunamis that are affecting Japan. As soon as the news broke, and we began to hear of tsunami warning for our area, I immediately realized how under prepared I was for a natural disaster. The thing that dro ...more
Here are some of necessary the tools for hobby crafting and diorama making. This model maker uses wood rasps, sanding pencils, wire cutters, small pliers, a box cutter, a wood carving knife, and a Japanese pull saw. When building miniatures you may find yourself making your ow ...more
This video shows you how to create a hollow book for keeping secret things inside. To the outside world the book looks normal, but only you know what goodies you have stored inside. You will need an old hardcover book, wood glue, Razor knife, steel ruler, brush, pencil, and cu ...more
Need a change? Brighten up your kitchen and give your cabinets a new look with a fresh coat of paint. In this tutorial, learn how to paint your kithcen cabinets a fast and efficient way. You Will Need: • A screwdriver • Grease-cutting cleanser • A sponge • Wood putty • A ...more
Stencils allow you make an image for easy duplication. The stencil can be used for tagging, fabric painting, t-shirts, or whatever else you want. Follow along with the steps in this video from Piece of Craft. You will need an X-acto knife or a wood burning tool (for advanced s ...more
In this tutorial, we learn how to begin using a woodcarving knife. Before you go into the detail, you will want to make sure you have it carved right. The carving all starts in the block of the wood. There will be a couple initial cuts that you will do with a knife after marki ...more
One of the distinguishing aspects of Trafficmaster Allure vinyl flooring is that it requires very little effort to cut the pieces to whatever length you need. All you do is score a line across the piece, then fold it in half! It snaps cleanly into two new pieces. This quick vi ...more
With the economy as brutal as it is, more people than ever are focusing on fixing what they've got rather than building or buying new furniture and decor. And oftentimes, a fresh coat of paint is all that's needed to turn a yucky old chair your mom passed down to you into a da ...more
Ryan teaches us how to make a trapeze spring snare to catch small game in this video. You will need: finishing line, a knife, paracord, and natural living wood. the trap will have two snares built into one mechanism. Start off by gathering all your wood and then place a stake ...more
Understanding how a knife most likes to cut wood is key to doing any woodcarving. In this video tutorial, a pair of disembodied hands will demonstrate, step by step, a method for efficiently carving out the bowl of a spoon with a hook knife. (Said hands use a blank of basswood ...more
In this video we learn to make fondant flip flops to decorate cakes. Grab your fondant and mix in your various colors. You can have as many colors as you want but should have at least two. Roll out your first color to your desired thickness. Use a butterfly cookie cutter to cu ...more
What do you get when you take a run-of-the-mill kitchen knife and add a simple synthesizer circuit? Behold, the Syntheslicer! Creator Jonathan M. Guberman writes: The Drawdio is a toy that attaches to a pencil and uses the conductive properties of graphite to make noise from ...more
If you're into fingerboarding, then you're going to want to watch this video tutorial to see how to improve your fingerboard skills. Watch to learn how to make a wooden fingerboard. With just a few materials, your finger-skateboard will be up and running in no time. Supplies: ...more
Researchers Hiroto Tanaka and Isao Shimoyama (of Harvard University and University of Tokyo) have constructed a tiny replica of the swallowtail butterfly. The crudely made model uses just balsa wood, rubber bands, and a steel wire crank. The goal is to better understand the bi ...more
I will show you how to make a loud whistle from a twig from a sycamore tree. In fact they are so loud that they could be used in an emergency situation to attract attention from potential rescuers. The international distress signal is 6 whistle blasts in quick succession. The ...more
Carving a net needle from wood is probably easier than you think as long as you have your trusty Swiss army knife at hand. It has a wide array of available tools in a small unit. First you will need a piece of balsa wood. It should be 1/8 of an inch thick by 3 inches wide and ...more
In order to repair stripped screw holes in wood, you will need the following, a hammer, screws, matches, awl, a flat headed punch, a utility knife, and side cutters. Cut off the tips of the wooden matchsticks. Place matchsticks in the hole, after you remove the strikers. Tap ...more
In this tutorial, we learn how to use foam to make diorama terrain. Foam will make a realistic diorama because it comes in so many different shapes and sizes. You can buy this from hobby shops and even online. To put these together, you will simply use some wood glue. You can ...more
Learn how to butterfly a chicken breast and pork chop. For this technique you will need a sharp boning knife and a cutting board.
Check out this science video to see how to make a solar-powered miniature car. To make this solar-powered mini car, you'll need some balsa wood, a small motor, two steel rods, four wheels, four washers, a straw of any color, two gears, a solar cell, hot glue gun, a tape measur ...more
In this video, we learn how to modify your machete for the bush. First, you can sharpen your blade on a piece of wood. You will produce wood shavings that will produce fire as well. Push down on the sides of the knife as well as base and on the tip and middle. Make sure you sl ...more
Start by putting tape around the area that you want to patch. This will keep the wood filler from getting all over the rest of the floor. If there is anything down in the floor like dog hair or crumbs make sure you get that stuff out before you put the wood filler in the area. ...more
Whittling seems hard, but not with this video tutorial... watch to learn how to carve a teeny wooden mouse with a small knife, sander and drill. These are stop motion animated instructions. See how to carve a miniature (under 1-inch) mouse out of wood with Steve Tomashek. Th ...more
Tim Carter demonstrates how to remove insulated glass panels from either side of a front door. Replacing the sidelights on the front door is possible. Just follow these steps for glass replacement. If the insulated sidelight glass panel on your front door goes bad, it can be ...more
Check out this step by step instructional video to learn how to make a Cosplay Sword from cardboard and wood! Make sure you have all of the following materials to start making your Cosplay sword: spray paint, hard cardboard, wooden dowel, bendable metal wire, silver colored ta ...more
Dan "The Lobster Man" Zawacki demonstrates how to make campfire lobster tails. First, quarter lemon halves. Then, butterfly the lobster tails by pushing on the tail. Use shears and cut the underside of the lobster down the middle. Flatten the tail a little more and use a knife ...more
The video guide shows us how to make our very own willow whistle. -Find a willow branch with green bark, cut a small wedge into the bark and in the wood. -Cut into the bark in a ring around the stick at least 2 inches behind the wedge notch. -Bang on the stick using the knife ...more
This video is a demonstration of how to decorate cut-out cookies to make pretty butterflies and ice cream cones. Use any cut-out cookie recipe that holds its shape well. First spread a little buttercream frosting on the cookie. This will serve as a glue for rolled fondant. Use ...more
Aspiring artists? Try your hand at painting with acrylic paints with this instructional video. Follow these tips & be on your way to creating a personal masterpiece. You Will Need: • A painting surface • Acrylic paint • Brushes • Gesso • Fine sandpaper • A medium • A p ...more
Step 1. Understand that opening a coconut requires a considerable use of precise force. Because you are using a knife or cleaver, it is very important that you keep your fingers and other body parts away from the blade. Step 2. Clear off a stable cutting surface. Step 3. Begin ...more
This makeup palette is the Forest Fairy Sprite Wood Nymph created by MissChievious. Begin with regular foundation. Get a little dark gold and golden cream eyeshadow with a knife & mix it into foundation. Take a large makeup blush type brush & put green shadow around top & side ...more
Clothespins are pretty innocent-looking, but with a mod here and a hack there, that innocence quickly turns into danger. Well, sort of. In this project, we'll be turning an ordinary spring-action clothespin into powerful matchstick and toothpick shooter that can shoot apples a ...more
Ask 100 chefs what the most important tool in their kitchen is, and you'll get 100 chefs saying the exact same thing: their set of knives. For home cooks and professional chefs alike, nothing is more important (or exciting) than a good knife. A good knife allows you to work mo ...more
There may be no kitchen appliance as controversial as the garlic press. Professional kitchens and many avid cooks despise it, while others staunchly defend it. On the one hand, Julia Child called it a "wonderful invention." On the other hand, Anthony Bourdain, in his must-rea ...more
After years of making do with a cheap knife, I finally bought a really good 8" chef's knife—a Henckels, although I was also eyeing a Global santoku. It quietly but literally changed my life. I don't have amazing knife skills, but having a great piece of equipment in my hands ...more
Magnetic knife strips are really handy. They allow for the removal of that huge knife block on your countertop, freeing up valuable counter space. They allow for easy access to your knives as you can mount them pretty much wherever you want. Plus, they look really cool, too! ...more
One of my favorite things to do when I visit my parents is cook. Aside from the fact that I adore cooking with my mom, there's something comforting about returning to the kitchen that I first started playing in 20 years ago. Nearly all of the tools and appliances are the same ...more
I want my Halloween costume to take as little effort as possible and be cheap—extremely cheap. That means I don't want to pay 50 bucks for some costume online or spend all day playing with liquid latex, and I most definitely do not want to visit a super crowded costume store i ...more
There is no greater food to master than steak. If you can make a steak that's only marginally better than your neighborhood Applebee's, you'll still have friends waiting outside your door for steak night. And if you can make steak as good as that expensive gourmet steakhouse y ...more
For me, the smoky brilliance of a good barbecue can't be beat. The way the smoke flavor seems to permeate every part of the meat is, in my opinion, the closest thing we have to food magic. Throw a piece of meat in a smoker with some select wood choices, wait a few hours, and s ...more
There's something about the world of steampunk that fascinates me. WonderHowTo has plenty of steampunk projects, like the hardware chess set, binocular goggles, and even a lesson on fashion. But nothing screams steampunk more than nevets_mcd's hard drive case. This case proj ...more
This article will show you how to make a shutter release cable for a Canon camera. It took me about half an hour once all of my materials were gathered. I came in at a total of about eight dollars. It has three switches and buttons. The black button on mine triggers the auto f ...more
Fire. It’s everywhere— always has been. From the Ordovician Period where the first fossil record of fire appears to the present day everyday uses of the Holocene. Today, we abundantly create flames (intentionally or unintentionally) in power plants, extractive metallurgy, i ...more